[REQ_ERR: COULDNT_RESOLVE_HOST] [KTrafficClient] Something is wrong. Enable debug mode to see the reason. Benchtop Machines > Another Warco WM18 CNC conversion (BFclone) - Page 11

User Login

Remember me
Calendar It is currently 28.01.2020

Review

Cnc conversion of WARCO WM18

Recommend you visit thierry lasry dr woo
118 posts В• Page 380 of 517

Warco cnc conversion

Postby Shagal В» 28.01.2020

Daniel Welch and Leroy Gregory were listed on either side of Daniel Mudd in this census.

Help Remember Me? Last Jump to page:. Thread Tools Show Printable Version. This time I'm aiming for something a bit different. WM16 There are plenty of resources detailing conversions of this machine and variants on the internet and it seemed a logical choice both in terms of size and price so I went ahead and bought it.

I have purchased 2HSS86H closed loop hybrid drives with 2 x 8. I should say that I've been advised, correctly I believe, that these motors and drivers are oversize for this application but i'm going ahead with this approach because I got the motors and drivers at a giveaway price from a mate's incomplete router project! Got a couple of ideas for the motor and bearing mounts but will have to take a good look at the mill before I start First off is a stripdown, clean and assessment I'll post again afterwards with some more info.

Those motors are far, far to big and will only slow the machine down believe it or not. I'm not looking for speed. I'm hoping to keep the motors and drivers for my next project But at the risk of sounding dumb, why should the larger motors affect top speed? Surely not through inertia? I suppose that the higher power means that current switching will be slower If I run them at plenty high voltage this should offset switching rates through the windings The motors will never be under any real load and should never get warm either which will reduce internal resistance after extended periods and again offset speed at which current flow can be changed though the windings over smaller motors..

Well you seem to have it sorted then. I have a WM18 mill with nema 23s with reduction at 68V and am drives and it is fine. You will need to do some more research if you think nema 34 8. Clive The more you know, The better you know, How little you know. I'll use what I've got and hope that it's adequate. I want to use the motors and drives for a much bigger CNC router project later But thanks for the input, I'll consider it when I build my next mill.

This mill is more to enable me to play with these drives and whatever controller before my router build. Incidentally, I'm going to direct drive the Z axis I'll keep you posted as to how this pans out!

Replies: 15 Last Post: , PM. Replies: 21 Last Post: , PM. Replies: 22 Last Post: , PM. Replies: 33 Last Post: , PM. Replies: 45 Last Post: , PM. Bookmarks Bookmarks Digg del. Aluminium Profile Type Router APT High speed, high hardness end Tooling Fixture Plate for Milling Greetings from The Great State of Comments sought on new build: A Denbigh model D conversion? Hi from Croatia 0 replies, latest reply by nisde , 21 Hours Ago.

Anyone here got a Boxford VSL? Steel tube build 7 replies, latest reply by Machinegreen , 1 Day Ago. Game on! Laser conversion for router 1 replies, latest reply by Boyan Silyavski , 1 Day Ago.

Help please. Dip switches and mach DIY Laser levelling using webcam Was about to get a toy- then I did Troubleshooting non responsive Luthier CNC 80 replies, latest reply by bluesking , Joe's xx steel and Newbie from NZ 56 replies, latest reply by rjsutton , 2 Weeks Ago.

First Build - Yet Another Alu Feeds and speeds. Some tips for a L Style Gantry on a sized Starting to design out my build, Cnc Machine wanted 1 replies, posted by franky , 17 Hours Ago. Laser conversion for router 1 replies, posted by Leadhead , 2 Days Ago. Warco VMC for sale - Perfect for Denford Triac 0 replies, posted by opentoideas , 2 Weeks Ago. Vortec Cold air gun model CNC Backup Gecko g 0 replies, posted by marbles , Traffolyte Sheets for sale 3 replies, posted by Conor , All rights reserved.

Warco CNC Retrofit, time: 1:07
Tokazahn
Moderator
 
Posts: 829
Joined: 28.01.2020

Re: warco cnc conversion

Postby Bacage В» 28.01.2020

By conversioj in forum Benchtop Machines. Reviews There are no reviews yet. What's the spindle speed like, and what kind of motor and control does it have? Thanks again. Http://perrfilrily.tk/the/capture-the-screen-on-windows.php about to get a toy- then I did

Mikanris
Guest
 
Posts: 632
Joined: 28.01.2020

Re: warco cnc conversion

Postby Dishura В» 28.01.2020

If I run them at plenty high voltage this should offset switching rates through the windings Add to basket Quick View. But at the risk of sounding dumb, why should the larger motors affect top speed?

Mikajinn
Guest
 
Posts: 397
Joined: 28.01.2020

Re: warco cnc conversion

Postby Dailkree В» 28.01.2020

Replies: 24 Last Post:PM. There was just cnf room to mount a limit switch for conversion on top of the saddle. Follow us on Twitter. Got a link of ideas for the motor and bearing mounts but will warco to take a good look at the mill before I start Subscribe Now Cnc savings Delivered to your door.

Bagis
Guest
 
Posts: 223
Joined: 28.01.2020


453 posts В• Page 255 of 446

Return to Review



 
Powered by phpBB В© 2008-2014 phpBB Group